Water heaters are the safest to use
Water heaters are strictly forbidden to be installed in the living room, dining room, bedroom and bathroom. Because the water heater consumes a lot of oxygen, it is easy to cause dizziness and nausea. In severe cases, it will cause carbon monoxide poisoning.
It is forbidden to use in-line water heaters. The direct-flow water heaters are taken from the room because of the oxygen required for combustion. The flue gas generated after combustion is also discharged indoors. The ventilation is not good and it is easy to cause carbon monoxide poisoning. The water heater must be installed with a flue, and attention should be paid to indoor ventilation when using it. The flue of the exhaust gas must be led to the outside and a windshield is installed.
The air source of the user's home must be consistent with the applicable temperament of the water heater, and should not be mixed to avoid danger. Gas facilities such as gas water heaters and wall-mounted boilers must be installed by qualified professionals to ensure the safety of you and your family.
Before using the gas water heater every time, you should check whether the room where the water heater is installed is well ventilated. When using the water heater for a continuous bath, it should be kept well ventilated. If the room where the water heater is installed is found to be filled with wind or smoke from the flue, it should be suspended. Use the water heater; if it is found to be black smoke or fire, it should be immediately deactivated and sent for repair.
Natural gas cookers should be used like this
Natural gas must be used for the use of natural gas. When igniting, first open the front valve of the stove, turn the switch knob on the stove to squat down, hear the sound of “咔嗒â€, and then release the hand after the piezoelectric body ignites the natural gas; when the flame is turned off, first close the front valve of the stove, wait for the flame After the auto is extinguished, turn the cooker switch knob to the off position.
According to national regulations, the life of gas cookers and natural gas water heaters is 8 years, and must be replaced when they expire. Excessive use of gas appliances will cause gas leakage due to aging of internal components, which may cause problems such as flameout in the middle and failure of safety devices.
Pay attention to the following points when using a wall-mounted boiler
1. Turn off or lower the radiator valve in the unoccupied room. In the case of a large housing area, a large number of rooms and a relatively small population, the radiator valve of a non-resident or low-frequency room can be turned off or down to reduce gas consumption.
2. Do not turn off the home, and adjust the temperature gear to the lowest level. When no one is in the house, many people are used to shutting down the boiler. After the shift, the boiler is adjusted to high-grade for rapid heating. This is very unscientific. Because the temperature difference between the room temperature and the set temperature of the boiler is large, the boiler needs time to run on fire, so that not only does it not save energy, but it will waste more gas, and there is a danger that the boiler or the radiator will be frozen. Therefore, before going to work, just turn the heating temperature adjustment knob of the boiler to “0â€, and then adjust the boiler heating gear to the temperature you need after work.
3, no one in the home long-term is best to drain the boiler and the radiator water, so that neither the use of natural gas nor the fear of the boiler or radiator being frozen.
4, wall-mounted boilers are strictly prohibited to be installed in the living room, dining room, bedroom and bathroom, because the wall-mounted boiler consumes a lot of oxygen when used, it is easy to cause dizziness and nausea, and it will cause carbon monoxide poisoning in severe cases.
5. Be sure to purchase qualified gas appliances produced by qualified regular manufacturers. Please install them when installing. Do not connect the water pipes to the gas pipes.
Aluminum Oxide Grinding Wheels
White alumina grinding wheel is made by sintering first-grade sand, high-quality alumina and binder at high temperature, also known as ceramic grinding wheel. Wear-resistant and durable. It has high hardness, brittle abrasive grains, sharp edges and corners, strong grinding ability, low calorific value, high temperature resistance, acid and alkali corrosion resistance, high efficiency and good self-sharpening. The grinding products are smooth and delicate
White alumina Bench Grinding Wheel, suitable for grinding steel with hard material and strong heat sensitivity. Such as grinding of hardened steel, high carbon steel, general high speed steel, alloy steel, stainless steel, etc. Mainly used for grinding and forming grinding of tools, cutting tools, molds, gears, threads, thin-walled parts, etc
Each of our products is inspected and carefully packaged before being sold to customers, but we do not rule out that there will be accidents. If you accidentally received an unsatisfactory product, please feel free to contact us and we will replace it for you or you can choose to return it. You can also contact us with product questions, we will do any answer for you and will try our best to solve the problem until you are satisfied.
Kemei produce and aim on the following types grinding tools, such as aluminum oxide grinding wheel, silicon carbide Grinding Wheels , mounted points, Diamond Grinding Wheels, CBN Grinding Wheels and all types of saw blades and cut off wheels.
If you need any type of grinding tool or professional advice about grinding on your workpieces. Don`t hesitate to contact us!
Aluminum Oxide Grinding Wheels,Red Corundum Wheel,High Speed Grinding Wheel,Brown Corundum Wheel
Henan Jinlun Superhard Material Co., Ltd , https://www.jinlungrindingtools.com