Device method for large motor bearing housing

Home>Bearing knowledge>Installation method for large motor bearing housing
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Device method for large motor bearing housing

Source: China Bearing Network Time: 2014-09-09

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
Device method for large motor bearing housing:
ㄒ唬5. 亟 莞 莞 耍 1、 1、 1、 1、 1、 1、 1、 1、 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固 紧固The practical length of the hole and the length of the check screw can be appropriate. The anchor plate should be closely attached to the base; the anchor screw should be straight with the anchor plate.
2, the most common screw for the foot screw is double screw; the device is convenient; there is also a screw with a T-shaped shape; the screw of this kind is laid down from the top; the screw is placed in the in-line hole of the anchor plate Then rotate the 900 screw to be locked by the anchor plate. Before the screw is tightened, the lubricant should be pre-coated on the thread.
Ç—5. The bottom plate of the large motor is mounted; it is usually welded by steel plate; or it is welded by I-beam and channel steel.
The bottom plate of the motor has the whole; there are also blocks. Their function is to support the motor; and the dynamic and static load of the motor is transmitted to the base; and the scale and the gap of the motor and some devices are kept unchanged.
1. Remove the oil before the bottom plate device; remove the anti-rust paint. Especially in the connection with cement irrigation; use a paint remover and a steel brush to clean it; then wipe it with a cloth; the best one can pre-brush a layer of cement slurry. .
2. In the clearing of the bottom plate, it should be noted whether the bearing seat surface and the stator base device surface can be scratched or rusted; if similar defects are found, use enamel and sandpaper to trim.
3. The bottom plate of the new device should have strict requirements on the base; the base should be solid; under the condition of accepting static load and dynamic load; the bottom should not sink. To avoid the sinking of the motor root; generally under the root irrigation After the preloading is carried out; the preloading component is generally 1.5 to 2.5 times of the component of the motor device. The elevation is continuously measured during the preloading process; the sinking condition is investigated; the device is allowed to be dried after the basement is stopped. For example, The steel plant pre-presses the root at the beginning of the rolling mill motor of the 1150; the pre-pressing component is about twice the total weight of the motor; after 48 hours, the root sinking is 2 mm.

Recommend to friends comments close window

Bearing related knowledge
How does the KOYO bearing cage data affect the bearing operation? How does the hub bearing be normally protected?
INA bearing operation to check the protection of the bearing when the bearing is in the bearing capacity of the grinding joint bearing


This article links to http://
Please indicate the bearing network http://

Previous:Smoothness of plain bearings: Mechanical engineering data: Rolling bearing steel

Abs Rod sold by AHD,it's quality has been rigorously screened, with light weight, good chemical resistance, long service life, good heat preservation, smooth inner wall, no scale, no bacteria, low friction coefficient and small water flow resistance (flow rate can be increased by 30%) High impact strength, simple connection, etc.

Product

Diameter(mm)

Length(mm)

Color

Density(g/cm³)

ABS Rod

20-200

2000

Nature

1.06

Application:Building model, hand-made, pharmaceutical industry, beverage pipe, compressed air piping, environmental engineering, chemical pipelines, etc.

ABS Rod

Abs Plastic Rod,Natural Abs Plastic Rod,Abs Rod ,Abs Plastic Bar

Shenzhen Anheda Plastic Products Co.,Ltd , https://www.ahdplastic.com