Tile paving is a big project. A kitchen and bathroom in a home will generally choose tiled floors and tiled walls. If the tiles are not properly affixed and left untouched, even if it is not a big problem, the owners may feel bad and depressed. Tiles are, the owners must pay special attention! Of course, this requires us to know the steps of laying tiles and some precautions, so as not to look over when we go to work! Below, Xiao Bian took everyone to know about paving tiles and the price of it!
The tile paving step is parsed as follows:
Tile Stirring Step A Stirring
Before preparing the adhesive, the tile should not be submerged, but use a wire brush to remove the loose material on the back of the tile and use a damp cloth to remove the dust from the back of the brick. Then put the water or emulsion in the mixing tank at the ratio recommended by the manufacturer until the adhesive is homogeneous and free of agglomerates. The adhesive after initial stirring should be left standing in a mixing drum until the manufacturer's recommended ripening time has passed.
Tile paving step two batches
With the straight edge of the tooth spatula conforming to the required thickness of the adhesive layer, the agitated adhesive is batched onto the base surface, and the adhesive layer is combed into uniform strips along the direction of the tile seam. The purpose is to control the thickness and amount of the adhesive and make the tile attachment area more uniform.
Tile Laying Steps Batch Tiles
A thin layer of adhesive was also applied to the back of the tiles before the tiles were laid. Although this double batch method uses more materials and working hours, it can guarantee the quality and durability of the paste.
Tile Paving Step Four Tiled
During the binder cooling time, the prepared tiles are laid in place and moved slightly perpendicular to the carding direction to expel the air under the tiles. After putting it into place, tap it with a rubber mallet and adjust the surface flatness and straightness of the seam with a cross-positioning bracket of the appropriate size.
Tile Laying Step 5 Clean up in Time
Paved bricks should be cleaned in a timely manner, especially to remove residual binder. After the qualified adhesive is hard-hardened, it is not easily removed even on the surface of the ceramic tile. Cleaned tiles should be immediately placed with signs for isolation, to avoid contamination or disturbance, until the next caulking process.
Tile Laying Considerations
1, before paving, the ground should be fully wet, according to the design requirements to determine the thickness of the mortar combined layer, playing horizontal lines on the wall and pre-row on the ground line to ensure that the room floor tiles in a unified level.
2. When laying, keep the horizontal position, use rubber hammer to make it tightly bond with mortar, and adjust its surface flatness and slit width. The slit width is generally 3-5mm.
3. When paving the floor tile, the four corners are pressed at the same time to make parallel contact with the mortar, and the cable is 2-3 cm higher than the cable, and then hit with a wooden hammer or a rubber hammer, and the face is leveled with a level ruler. After laying out a piece, lay it on both sides or back. If there is a subsidence phenomenon, the tiles should be lifted and then laid flat with mortar and then laid.
4, bathroom tiles should be set aside about 1% of the slope, and lower than the outer floor tiles about 10mm. The slope of kitchen tiles should be appropriately reduced.
5. Apply about 10 bricks per paving, check the surface flatness and slope with a ruler, and adjust the brick seams properly to keep the tiles clean.
Tile price
1, the old method to 12-16 yuan per square meter, you settle in accordance with the actual area.
2, now popular with tile adhesive thin paste method, a manual construction area of ​​nearly 20 square meters, about 8-10 yuan per square meter, the premise is to find the grassroots level.
Editor's Reminder: The information on tile paving knowledge and tiling price is shared here, hoping to give some help to friends who want to tile. If you want to know more information, you can pay attention to this website information, or go to this website to find more favorite products!
Tile Tile Paving Floor Tile Tile Price Tile Adhesive
PVDF is short for Polyvinylidene Fluoride, it is a kind of Fluoride plastic with excellent physical mechanical and chemical properties, PVDF chemical stability make it no reaction with other substances, in this case it have excellent corrossion resist property and can be used for strong acid. In this case PVDF Diaphragm Valve is most suitable for chemical industrial, semi conduct industria. The working temperature could up to 140 degree. Standard fit for ANSI, JIS, DIN, pressure rate PN10 bar. Manual operate and pneumatic actuator operation both avaliable.
Ningbo RMI Plastic Co.,Ltd offer PVDF Diaphragm Valve with specification:
Size range:DN15~DN250 (1/2 inch ~ 10 inch)
Body materials:PVDF
Diaphragm material:PTFE,EPDM,FPM,NBR,NR
Connection: Flange ANSI CL150, JIS10K, DIN PN10; Socket: DIN, ANSI, JIS
Design pressure:0.25~1.0Mpa (PN2~10 bar)
PVDF Diaphragm Valve
PVDF Diaphragm Valve,PVDF Diaphragm Valves,Diaphragm Valve PVDF,PVDF Valve
Ningbo RMI Plastic Co., Ltd. , https://www.rmiplast.com